Heating Flow Switch Error (Ireland) Pressure Sensor Error (UK)
The E164 error code on Baxi boilers indicates heating flow switch error (ireland) pressure sensor error (uk).
Baxi E164 means: heating flow switch error (ireland) pressure sensor error (uk). On this component the documented failure modes are wiring, connector or harness of the pressure sensor damaged or loose, flue or air intake blocked or restricted or the pressure sensor has failed — short circuit or open circuit. You can safely reset the boiler once — if E164 returns, do not keep resetting. A qualified heating engineer should diagnose the root cause.
What Does E164 Mean
The E164 code is shown by the boiler’s control board when it detects heating flow switch error (ireland) pressure sensor error (uk). The boiler then stops instead of continuing to run in that condition: the code is the appliance reporting a problem, not proof that the boiler is broken.
| What you see on the boiler |
|---|
| The display shows E164 and the boiler stops until the fault is cleared |
Common Causes
The manufacturer does not publish a cause list for this specific code. The causes below are the failure modes documented for the same component on other boilers, confirmed by the service literature of 4 different manufacturers.
| Cause |
|---|
| Wiring, connector or harness of the pressure sensor damaged or loose |
| Flue or air intake blocked or restricted |
| The pressure sensor has failed — short circuit or open circuit |
| Heat exchanger fouled or partially blocked |
| System water pressure too low, or a leak somewhere in the system |
| Too many reset attempts: the boiler has locked itself out |
Safety Warning
E164 involves electrical or pressure-related components. Do not attempt repairs without proper qualifications. Ensure the boiler is electrically isolated before any inspection. If you notice water leaks, unusual sounds, or pressure anomalies, contact a qualified heating engineer immediately.
Parts & Prices
Prices shown are indicative. Actual prices and availability vary by region.
Step-by-Step Diagnosis
1. Check the boiler pressure gauge — normal operating pressure is 1.0-1.5 bar (15–22 psi) when cold. 2. Inspect all visible pipework, radiators, and valves for signs of leakage. 3. Check the pressure relief valve discharge pipe — if water is dripping, the PRV may be faulty or the expansion vessel has failed. 4. Test the expansion vessel — with the system cold and drained, check the Schrader valve on the vessel
air should escape at the correct pre-charge pressure (typically 0.75-1.0 bar, 11–15 psi). 5. Inspect the pressure sensor connections. 6. Check automatic air vents for signs of weeping
How to Fix It
Unplug and re-seat the connector of the pressure sensor, then check the harness for chafing, corroded pins and breaks in continuity.
Inspect the flue and air intake along their whole length, including the outside terminal, and clear any obstruction or debris.
Measure the resistance of the pressure sensor with a multimeter and compare it against the manufacturer’s resistance-versus-temperature table; replace it if it is open circuit, short circuit or out of range.
Have the heat exchanger inspected and cleaned; if it is blocked by limescale or sludge the system needs a chemical flush and an inhibitor dose.
Repressurise the system to the pressure stated on the boiler — typically 1.0–1.5 bar (15–22 psi) when cold. If it drops again, look for a leak on pipework, radiator valves and the pressure relief discharge.
Stop resetting: the underlying fault is still present. Switch the boiler off and on to restore the reset attempts, then have the original fault diagnosed.
Refer to the Baxi service documentation for the detailed procedure. Only a qualified engineer should carry out these repairs.
Diagnostic Tools
TroubleAtlas Score
What Is the TroubleAtlas Score?
Every boiler model is independently evaluated and scored by TroubleAtlas across 6 dimensions: reliability, efficiency, parts availability, service network, value for money, and user satisfaction. The score helps you compare models and make informed decisions when choosing a new boiler.
See All Boiler Scores →Boiler Breakdown Cover
Boiler Breakdown Cover
Protect against unexpected repair costs. Cover plans include annual service, emergency callouts within 24 hours, and full parts replacement. Compare plans side by side and choose the level of protection that fits your home and budget.
Coverage Plans — Coming SoonConsidering a New Heating System
Considering a New Heating System?
If your boiler or heat pump is over 10 years old, replacing it with a modern condensing boiler or air-source heat pump could save you up to 30% on energy bills and significantly reduce your carbon footprint.
Compare Heating System Prices →
YouTube Channel
Watch the fixes. Follow the channel.
Step-by-step boiler repair guides, equipment reviews, and heating system comparisons from qualified engineers.
New fixes every weekFix in 5
Quick fixes for common boiler faults explained in under 5 minutes
Boiler Comparator
Side-by-side comparisons of popular boiler models
Boiler Reviews
Independent reviews with TroubleAtlas Score ratings
Find a Specialist
Don’t fix it alone. Find a trusted heating engineer near you.
TroubleAtlas connects you with vetted local heating professionals who can inspect, diagnose and repair your boiler safely — no guesswork, no unnecessary call-outs.
Local heating professionals are coming to your area
We’re onboarding Gas Safe registered and licensed HVAC engineers city by city. Check back soon, or search above to see current availability.
TroubleAtlas Pro
Get cited by AI. Get found by customers.
TroubleAtlas Pro puts your business in front of homeowners searching for exactly this fault, and structures your listing so AI assistants can cite you as a trusted source.
- ✓ Appear on error code pages viewed by thousands of homeowners
- ✓ AI assistants cite your listing as a verified local specialist
- ✓ Receive direct leads with customer name and contact details
- ✓ TroubleAtlas Certified badge for your marketing materials
Affected Models
Baxi models that can display fault code E164:
| Model Family | Output Range | Frequency |
|---|---|---|
| All Baxi models | — | Possible |
Frequently Asked Questions
Unplug and re-seat the connector of the pressure sensor, then check the harness for chafing, corroded pins and breaks in continuity. According to the technical documentation, this is the first check on the list for E164.
E164 is not classified as a high-severity fault, so the boiler can be reset once. If E164 comes back, stop resetting: the underlying cause is still there and needs a qualified heating engineer.