Zanussi washing machines fault codes
Every Zanussi washing machines fault code we have documented, with what it means. Pick yours to see causes, checks and the parts involved.
● 45 codes documented
Zanussi uses 45 fault codes on its washing machines, shown on the display when the machine stops — among them E10, E11, E12, E13, E20. Each one points to a specific part: on this page you find them all, with what they mean.
How to read the code on the display
On most Zanussi appliances the code appears on the display when the cycle stops, or is spelled out by a sequence of blinking lights.
Write the code down before switching off: many machines clear it when unplugged, and without the code the fault has to be found from scratch.
Replacement parts
Tools you'll need
Find a specialist
TroubleAtlas Pro
TroubleAtlas Certified
What is the TroubleAtlas Score?
Beyond fault codes and specialists, we rate the reliability of appliance brands and models — a transparent score that owes nothing to the manufacturer. The reference to check before you buy or repair.
See all appliance scores →TA YouTube Channel
All Zanussi codes
45 codes, in order. Click one to open its page.
| CODE | WHAT IT MEANS |
|---|---|
| E10 | Water fill fault machine not filling or fill taking too long |
| E11 | Slow or incomplete fill fill taking longer than expected |
| E12 | Water level sensor not confirming fill has completed |
| E13 | Anti-flood device triggered water detected in the machine base |
| E20 | Drain fault machine unable to drain within expected time |
| E21 | Slow drain machine draining but taking longer than expected |
| E22 | Drain pump monitoring fault pump running but flow not detected as expected |
| E23 | Drain pump fault pump motor failure |
| E24 | Drain pump relay fault relay on control board controlling the pump |
| E33 | Incongruency between pressure switch readings the two pressure monitoring systems are not in agreement |
| E34 | Incongruency between pressure switch and secondary water level sensor |
| E35 | Water level too high overfilling detected |
| E36 | Anti-boiling pressure switch sensing circuit fault |
| E37 | First-level pressure switch sensing circuit fault |
| E39 | High-voltage pressure switch or anti-flood device fault |
| E3x | Pressure switch and water level system |
| E40 | Door lock fault general group code |
| E41 | Door open machine not detecting the door is closed |
| E42 | Door lock mechanism fault mechanical locking failure |
| E43 | Door lock control circuit fault electrical fault in door lock circuit |
| E44 | Door open signal not received by control board |
| E45 | Door lock relay fault relay on control board that controls door locking |
| E4x | Door lock system |
| E50 | Motor fault general group code |
| E51 | Motor power triac short circuited |
| E52 | No signal from motor tachometric generator |
| E53 | Motor triac sensing circuit fault PCB sensing circuit failed |
| E54 | Motor relay faulty relay on control board controlling motor power |
| E60 | Heating fault general group code |
| E61 | Insufficient heating during wash water not reaching target temperature |
| E62 | Overheating detected water temperature exceeding expected level |
| E63 | Heating element safety thermostat triggered |
| E64 | Heating element contact fault |
| E65 | Anti-flood device triggered during heating phase |
| E66 | Heating element relay contacts always closed relay stuck on |
| E67 | Power supply fault affecting the heating circuit |
| E68 | Heating relay fault or communication fault in heating circuit |
| E6x | Heating system |
| E90 | Communication fault between control panel and main PCB |
| E91 | Communication error internal control board fault |
| E92 | Communication error secondary module communication failure |
| E93 | Configuration fault machine incorrectly configured or configuration data lost |
| E94 | Incorrect cycle configuration control board data fault |
| EF0 | Anti-flood, overflow, or over-foaming detected |
| EH0 | Older model equivalent of E10/E11 water fill problem |